LeftyBassist.com

The online home for southpaw bassists.
It is currently December 25th, 2024, 11:55 am




Post new topic Reply to topic  [ 3 posts ] 
Author Message
 Post subject: Shielding Paint Questions
PostPosted: May 27th, 2011, 3:23 pm 
Offline
User avatar

Joined: March 14th, 2008, 1:45 pm
Posts: 3950
Location: Huntsville, AL
How is paint better/worse than copper tape? And do you have to ground pots, etc to the painted surface somehow (and if so, how?)

Thanks

M :mrgreen:

_________________
http://www.facebook.com/profile.php?id= ... ef=profile

www.twitter.com/ReallyMattRoss

Penguins is practically chickens.


Top
 Profile  
Reply with quote  
 Post subject: Re: Shielding Paint Questions
PostPosted: May 27th, 2011, 6:21 pm 
Offline
User avatar

Joined: March 10th, 2008, 7:00 pm
Posts: 1184
Location: Seattle, WA USA
Shielding paint is great for production shops where you want to maximize the shielding on your instruments while minimizing your time investment (most customers can't justify the aded $100 for copper foil shielding with soldered seams) One problem with shielding paint is that some products become flaky after several years, and this turns into a mess in your cavity

I personally use shielding foil on my custom instruments, and the Stewmac shielding paint only on those instruments where the bottom line is critical for a customer. The foil, if done right, will be every bit as solid 25 years from now as the day you installed it. You can also solder to it, which makes it easy to connect a ground lead to your pickup cavities

when using paint you should have a common ground wire connecting the cases of all your pots, the jack ground, the bridge ground, and your cavity grounds. I typically install a copper strip into each pickup cavity botton and one on the side of the control cavity, solder a ground lead to each of the pickup cavity strips, and then connect the four ground leads (both pickup cavities, jack/pots, and bridge) together into a lug. Once this is done I apply three applications of the shileding paint (per directions on the can) covering the copper strips in the cavities being sure to leave an area bare on the control cavity foil strip. once all of the electronics are installed I attach the ground lug with a screw to the bare spot on in the control cavity (it helps to pre-drill a pilot ole into the bare spot prior to installing the pots/electronics)

make sense?

all the best,

R

_________________
Moderator: Blueprinting and Bondo
Pickups: Honey Badger Pickups - Like Honey Badger Pickups on Facebook!
Basses: Regenerate Guitar Works - Like Regenerate Guitar Works on Facebook!


Top
 Profile  
Reply with quote  
 Post subject: Re: Shielding Paint Questions
PostPosted: May 28th, 2011, 8:43 am 
Offline
User avatar

Joined: March 14th, 2008, 1:45 pm
Posts: 3950
Location: Huntsville, AL
Makes perfect sense, thanks. I think I will stick with copper tape then. :ugeek:

_________________
http://www.facebook.com/profile.php?id= ... ef=profile

www.twitter.com/ReallyMattRoss

Penguins is practically chickens.


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 


Who is online

Users browsing this forum: No registered users and 14 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group  
Design By Poker Bandits